The Foundation of Plumbing Knowledge When Installing a Bathtub
The Foundation of Plumbing Knowledge When Installing a Bathtub
Blog Article
Do you find yourself interested in ideas around A Step-by-Step Guide to Installing a Bathtub?
Installing a bath tub isn't exactly rocket science, but it does require strong plumbing, woodworking, and occasionally, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately challenging task. If the old tub is readily easily accessible, the job can move easily; if you have to open a wall to eliminate the old tub as well as position the brand-new tub, the job is much harder. In either situation, the project is within a house handyman's skills, although you will certainly require a helper to move out the old bathtub as well as set in the new one. Make certain you have certified yourself for the task as well as fit trying it. Rather than hiring a specialist to take control of a halfway-completed task, it is far better to consider employing one prior to you begin. Chances are you may require an expert plumber to make tube links.
This short article will certainly help you set up a brand-new bath tub in your shower room if you have actually already gotten a brand-new tub as well as do not need to change the arrangement of your previous water system pipelines.
Your devices as well as material checklist must make up the following:
Planning for the Installment
First of all, the supporting framework provided with the bath ought to be fitted (if needed) according to the supplier's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets device to avoid stress on the bath tub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you use all of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, then the first thing you must do is detach the water. After doing so, activate the faucets to drain any water staying in the system. The process of removing the existing faucets can be rather troublesome as a result of the limited accessibility that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a fabric all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this process. Once the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Before moving on to fit the new taps, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bathtub
Making use of the two wooden boards under its feet, position the tub in the called for setting. The wooden boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 tiny factors.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the tub until the level reads level.
To mount taps, fit the bottom of the furthest versatile faucet port to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the water and inspect all joints and also brand-new pipework for leaks as well as tighten them if required. Load the bathtub as well as likewise examine the overflow electrical outlet and also the normal electrical outlet for leaks.
Ultimately, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and also securing around the tub must wait until the bath tub has actually been utilized at least when as this will certainly settle it into its last setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end gives a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin ensuring that the washers remain in area between the faucet as well as the sink. Protect the tap in position with the maker offered backnut. As soon as the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet connectors. The previous type should be attached to the tap ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, resulting in difficulties with moisture as well as feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and cartridges, and also are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to allow for the motion experienced when the bathtub is in use. The sealer can break relatively very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the market. It is recommended to fit the floor tiles utilizing water-resistant or water resistant adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that page about How to Install a Bathtub Yourself while looking around the web. Don't hesitate to set aside a second to share this write-up if you appreciated it. I value reading our article about How to Install a Bathtub.
Hot water gone? Dial here. Report this page